We have strong technical force that can be timely, quality, quantity supply, to provide clients with the best quality Autoguide Mobile Robot, Photoelectric Sensor Module, Mecanum Wheel Module and service. We are sincerely expecting your attention. We think that only by continuous self-improvement and enhancement of innovation ability can we maintain our brand and competitiveness.

Product introduction

1. Product features

Main features of wheel hub motor:

1. 1. DC servo motor is higher integration: less overall structural parts, integrating power, transmission and braking

1. 2. High precision control: high speed response, precise positioning, anti-interference;

1. 3. No brush: stable operation, low operation noise, high efficiency and energy saving, long service life;

1. 4. Each wheel has a separate motor drive, which can realize four-wheel drive.

2. Application scenarios

The product can power all kinds of tires. For example, ship blade, mecanum wheel, crawler, etc., meet the needs of different industries such as industry, scientific research, commerce, medical treatment, etc., with wide application, stable quality and large shipment.

3. Parameter table

The above parameters are for reference only. Our product technology is constantly updated and upgraded. At the same time, we also accept the customization and development of customers.

4. Product details

5. Factory and qualification

mobilelogisticsrobot4

mobilelogisticsrobot5

mobilelogisticsrobot6

mobilelogisticsrobot7

6. Instructions and precautions

Precautions

1. Avoid the risk of short circuit by placing the differential wheel hub motorin a wet place

2. Avoid the sharp objects close to the stator winding to prevent the insulation layer from damage and short circuit of the motor.

3. Do not use in dusty places.

4. Ensure good lubrication when the motor is running. 6. There is abnormal noise when the motor is running without load. Please check the source of the noise.

5. Small metal objects shall not be stacked next to the DC servo motorto avoid falling into the motor.

6. Do not use or store products in an environment where the pH range may cause corrosion or dissolution of products or packaging materials.

Instructions for regular maintenance

1. Do not change the power supply voltage at will, for example, 4.8V for receiver, 6.0V for improving the performance of servo motor to avoid excessive load of servo motor and determine the torque according to the nature of work and the length of swing arm.

2. Make good use of the vibration proof washer to protect the servo motor. When installing the servo motor, do not lock it too tightly, resulting in the deformation of the vibration proof washer.

3. When replacing the servo motor gear, ceramic lubricating oil must be used. Do not use mineral lubricating oil to avoid deterioration and easy fracture of plastic gear.

4. If your servo motor does not have the function of waterproof and dustproof, please avoid water or dust running into the servo motor.

5. For the maintenance of the servo motor, it is necessary to note that when installing or removing the coupling parts to the shaft end of the servo motor, do not directly hit the shaft end with a hammer.

FAQ:

What is the fault condition of servo driver?

A：The servo motor will place a bearing on the drive side and a bearing on the non-drive side to connect and support the motor shaft. Among them, the drive side bearing needs to support the axial and / or radial load of external mechanical connection, usually with large size and shaft load. The ball bearing of servo motor needs double protection and permanent lubrication. It needs strict maintenance in normal use. As the main wear part of servo motor, more than half of the faults of servo motor are usually caused by bearings. The specific status quo is various, for example: when the motor is rotating, it produces jitter, abnormal noise, etc., and the motor shaft is stuck. If the bearing fault of servo motor is not handled in time, it will bring secondary damage. As the rusty debris of the bearing flies into the brake or motor encoder, it will cause more serious losses.

We strongly believe that with our wealth of experience and quality assurance of High Quality 750W 220V 3000rpm 80mm 2.39nm AC Servo Motor and Driver, CNC Servo Motor, DC Servo Motor for Laser Cutting Machine, it will gain your favor. On the basis of consolidating quality first, we should also provide better products and services for customers. We have a firm of outstanding employees doing their best to make our firm stronger every day, and we can be proud of that.

Hot Tags: DC servo motor, China, manufacturers, suppliers, wholesale, custom, high quality, Mecanum Wheel, Agv Robot, Logistics Robot, Robot Core Components, Intelligent Module, Fingerprint Sensor

[[ProKeywords]]