Rov Thruster Marine Thruster

We constantly function like a tangible group to ensure that we can give you the very best high-quality and also the very best cost for UV Bacteria Killing Robot, Linear Absolute Encoder, Delta Ac Servo Driver. Our company adheres to the concept of 'technological innovation, pursuit of excellence, win-win cooperation, and sustainable operation', and takes 'customer first' and 'service satisfaction' as the eternal theme of the company. We warmly welcome new and old customers to inquire and patronize. We will work hand in hand with your company and will serve you with the best quality and the best price and we will become your best partner.

Product introduction

1. Product features

Main features of joint AUV motor:

1. 1. High integration: less overall structural parts, integrating power, transmission and braking

1. 2. High precision control: high speed response, precise positioning, anti-interference;

1. 3. No brush: stable operation, low operation noise, high efficiency and energy saving, long service life;

1. 4. Each wheel has a separate AUV motor drive, which can realize four-wheel drive.

2. Application scenarios

It can provide power for various machines. For example, ship blade, Mecanum wheel, crawler, etc., meet the needs of different industries such as industry, scientific research, commerce, medical treatment, etc., with wide application, stable quality and large shipment.

3. Parameter table

The above parameters are for reference only. Our product technology is constantly updated and upgraded. At the same time, we also accept the customization and development of customers.

4. Product details

5. Factory and qualification

6. Instructions and precautions

Precautions

1. The use environment shall be kept dry frequently, the motor surface shall be kept clean, and the air inlet shall not be blocked by dust, fiber, etc.

2. When the thermal protection of the motor continuously acts, it should be found out whether the fault comes from the motor or overload or the setting value of the protection device is too low. After the fault is eliminated, it can be put into operation.

3. The motor shall be well lubricated during operation. Generally, when the motor runs for about 5000 hours, the lubricating grease shall be supplemented or replaced. If the bearing is overheated or the lubrication is deteriorated during operation, the hydraulic pressure shall replace the lubricating grease in time. When replacing the grease, the old grease shall be removed, and the oil groove of the bearing and bearing cover shall be cleaned with gasoline. Then, zl-3 lithium grease shall be filled into 1 / 2 (to 2 poles) and 2 / 3 (to 4, 6 and 8 poles) of the cavity between the inner and outer rings of the bearing.

4. When the service life of the bearing is over, the vibration and noise of the motor will increase obviously. When the radial clearance of the bearing reaches the following values, the bearing shall be replaced.

5. When disassembling the motor, take out the rotor from the shaft extension end or the non-extension end. If it is not necessary to remove the fan, it is more convenient to remove the rotor from the non-shaft extension end. When withdrawing the rotor from the stator, the stator winding or insulation shall be prevented from being damaged.

6. When replacing the winding, the form, size, turns, wire gauge, etc. of the original winding must be recorded. When these data are lost, it is necessary to ask the manufacturer for them, and change the original design winding at will, which often makes one or several performances of the motor deteriorate, or even cannot be used.

7. When using the servo motor, pay attention to: keep the motor clean and free of dust; check the appearance of the motor frequently to see if there is any misplacement of parts; check the bearing frequently for replacement or oil filling, and check the incoming wire connector

Instructions for regular maintenance

1. Clean the dust, dirt and oil stains on the terminal, encoder and servo driver regularly.

2. Check the vibration and sound of the motor every day.

3. The insulation resistance shall be checked regularly to ensure good insulation. Generally, it shall be checked once a year.

4. For the servo motor with oil seal, it is better to replace the oil seal every year or 20000h.

5. Ensure the lubrication of servo motor bearing and change the lubricating oil regularly.

6. Ensure that the working voltage does not exceed ± 5% of the working voltage

We're going to commit ourselves to giving our esteemed buyers using the most enthusiastically considerate solutions for Rov Thruster Marine Thruster. In order to adapt to market demand, we have also been constantly optimizing and integrating company resources, striving to provide customers with cost-effective products. Honesty to customers, employees, and society are our important intangible assets, therefore, we insist on winning customers with integrity, and gaining customers' trust and respect with sincerity.

Hot Tags: AUV motor, China, manufacturers, suppliers, wholesale, custom, high quality, NightVision Patrolling Robot, Brushless Motor Robotic Joint, Spray Disinfection Robot, Permanent Magnet Brushless Dc Motor, Brushless DC Motor, In wheel Motor